TD62S350AFM 2001-12-05 1 toshiba bipolar digital integrated circuit silicon monolithic TD62S350AFM 1-channel darlington source-current driver the TD62S350AFM is a 1-channel noninverting source-current driver. the driver incorporates an input resistor which limits output pull-down resistance and base current. the driver is optimal for driving fluorescent display tubes and leds. when using the driver, pay attention to the thermal conditions. features ultra-small hson6 package with heat sink on rear large output voltage: v out = ? 50 v (min) large output current: i out = ? 500 ma (max) built-in input resistor: r in = 10 k ? input signal: high level active pin connection (top view) basic circuit diagram note 1: diodes shown using dotted lines are parasitic. do not use them. note 2: when using the driver, connect the output pin to the test pin. note 3: when using the driver, connect the p-gnd pin to the heat sink on the rear of the package. weight: 0.017 g (typ.) 10 k 2.6 k input 20 k 10 k v cc test output p-gnd rpd 5 k 1 2 3 input p-gnd nc 6 5 4 output test v cc
TD62S350AFM 2001-12-05 2 maximum ratings (ta 25c) characteristics symbol rating unit supply voltage v cc 0.5~50 v output voltage v out 50 v collector-emitter voltage v ceo 50 v output current i out 500 ma input voltage v in 0.5~15 v power dissipation p d (note 4) 0.78 w r th (j-a) (note 4) 160 saturated thermal resistance r th (j-c) (note 5) 25 c/w operating temperature t opr 40~85 c storage temperature t stg 55~150 c note 4: 114.3 76.2 1.6 mm glass epoxy film substrate cu heat dissipation pattern 100 mm 2 note 5: when an infinite heat sink is mounted. recommended operating condition (ta 40~85c) characteristics symbol test condition min typ. max unit supply voltage v cc 50 v output current i out ta 60c, t j 105c 130 ma input voltage v in 12 v output on v in (on) 2.0 5.0 12 input voltage output off v in (off) 0 0.8 v electrical characteristics (ta 25c, v cc 50 v) characteristics symbol test circuit test condition min typ. max unit output leakage current i cex 1 v in 0.4 v 10 a v in 2.0 v, i out 350 ma 1.8 2.0 output saturation voltage v ce (sat) 2 v in 2.0 v, i out 130 ma 1.5 1.75 v v in 3.6 v 240 350 a input current i in (on) 3 v in 12 v 1.1 1.6 ma v in (on) v ce 2.0 v, i out 350 ma 2.0 input voltage v in (off) 4 i out 500 a 0.5 v power dissipation i cc (on) 3 v in 5 v 0.8 ma output pulldown resistor rpd 168 240 312 k turn-on delay t on 0.1 turn-off delay t off 5 r l 125 , c l 15 pf 7.0 s
TD62S350AFM 2001-12-05 3 test circuit 1. i cex 2. v ce (sat) 3. i in (on) , i cc 4. v in (on) , v in (off) 5. t on , t off note 6: pulse width 50 s, duty cycle 10% output impedance 50 , t r 5 ns, t f 10 ns note 7: c l includes probe and jig capacitance. i ce x v cc v in v cc v in v ce ( sat ) i out i cc v cc v in i in ( on ) v cc v in (on) v in (off) v ce i out pulse generator input c l (note 7) (note 6) v cc r l 10% 90% 90% 10% 10% 50% 50% t on t off t f t r 5 v 0 v oh v ol output input 90% 50 s caution on application 1. the device does not include protectors such as an overcurrent protector and an overvoltage protector. applying excessive current or voltage may damage the device. thus, design with great care to prevent excessive current or voltage from being applied to the device. the device may also be damaged by short-circuits between outputs and power supply/ground. take care when designing output, v cc and gnd line. 2. if the TD62S350AFM is used to drive an inductive load (such as a motor, solenoid, or relay), toshiba recommends that the diodes be connected between pin 1 and pin 5 so as to absorb the counter electromotive force generated by the load. please adhere to the maximum ratings of this device. 3. be sure to mount the device in the correct orientation. make sure that the positive and negative power supply pins are connected the right way round. otherwise, the absolute maximum current and power dissipation ratings may be exceeded and the device may break down or undergo performance degradation, causing it to catch fire or explode, and resulting in injury.
TD62S350AFM 2001-12-05 4 package dimensions weight: 0.017 g (typ.)
TD62S350AFM 2001-12-05 5 preliminary land pattern preliminary pcb trace dimension 2.2 0.6 0.6 1.6 1.6 0.7 0.7 0.7 0.25 1.3 unit : mm 5 mm 10 mm
TD62S350AFM 2001-12-05 6 toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc.. the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk. the products described in this document are subject to the foreign exchange and foreign trade laws. the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba corporation for any infringements of intellectual property or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any intellectual property or other rights of toshiba corporation or others. the information contained herein is subject to change without notice. 000707eb a restrictions on product use
|
